Global Insulation

Protective coating systems for steel, pipe, tank and floor

Coatings that keep steel in service.

Global Insulation supplies and applies corrosion protection, waterproofing and thermal insulation for pipelines, tanks, steel structures and industrial floors — field-proven systems matched to the substrate and the environment.

  • 40+ years in construction materials
  • 4 coating systems, one supplier
  • DIN EN ASTM specified and tested
Technician wrapping a coated steel line pipe with viscoelastic tape on site
Joint protection on a coated line pipe

One supplier for the layer that keeps the asset alive.

Corrosion, water and heat decide how long a structure lasts. We select the coating or membrane that suits the service conditions, supply it, and put it on — for new-build work and for the repairs that keep older plant running.

Our range is built around epoxies, urethanes, acrylics, silicones and elastomers, and around tapes and membranes that have held up for decades under mechanical and chemical stress. Technical consultation comes with the material, from specification through inspection.

What we protect

Worker applying a protective wrap to a large-diameter steel pipeline
Pipeline coating work on site

Corrosion protection for steel, pipes and tanks

Welded seams, valves, flanges, bends and rehabilitation work on buried or submerged steel — the joint is where corrosion starts, and it gets the full system, not a patch.

  • HT-60 / HT-80 heat-shrink sleeves
  • UT butyl tape, DIN 30672
  • VE-19 viscoelastic system
  • EC 100% solids epoxy

Works with: PE, PP and FBE plant coatings; onshore and offshore lines; tank shells and bases.

Crew applying a self-levelling epoxy floor coating in an industrial building
Self-levelling epoxy floor, industrial hall

Epoxy and resin floors

Seamless floors for plants, workshops, warehouses and loading areas: prepared substrate, primer, the body coat the traffic calls for, and a finish chosen for chemicals and slip resistance.

  • Self-levelling epoxy
  • Epoxy mortar screed
  • Anti-slip finishes
  • Coving and detailing

Works with: new slabs and worn floors; food, pharma, automotive and logistics buildings.

Worker torch-applying a polymer-modified bituminous waterproofing membrane to a roof
Torch-applied membrane on a roof deck

Waterproofing

Roofs, basements, foundations and wet areas, detailed around upstands, drains and penetrations — with membranes that stay flexible through the temperature range the structure sees.

  • TA torch-applied membrane
  • SA self-adhesive membrane
  • BC bituminous coating
  • EM elastomeric acrylic
  • PU polyurethane
  • PVC 30 sheet

Works with: concrete, masonry, metal and timber decks; below-grade and exposed conditions.

Two technicians in protective suits spray-applying polyurethane foam insulation on a roof
Spray-applied polyurethane foam

Thermal insulation

Closed-cell polyurethane foam sprayed in place: it bonds to the substrate, fills the irregular shapes, and leaves a seamless surface with no joints to leak.

  • PU foam, roof and terrace
  • Tank and vessel insulation
  • Low water absorption
  • Protective top coats

Works with: flat and pitched roofs, terraces, cold rooms, tanks and pipework.

Where the work goes

Coating decisions are made by the service conditions, not the catalogue. These are the sectors we supply and apply into.

  • Oil and gas Line pipe, girth welds, valves, flanges and tankage.
  • Water and wastewater Pipelines, treatment structures and reservoirs.
  • Industrial plants Steelwork, vessels, bunds and production floors.
  • Bridges and highways Structural steel, decks and expansion joints.
  • Commercial building Roofs, basements, terraces and plant rooms.

The standards we work to

Systems are specified and tested against the standards your inspector already uses, and supplied with the documentation that goes with them.

Standards referenced by Global Insulation systems
DIN 30672Corrosion prevention tapes and shrinkable materials for buried pipelines.
EN 12068External organic coatings for corrosion protection of buried pipelines.
ASTMCoating and lining test methods for pipeline and tank work.
AWWAWater and wastewater pipeline coating and lining practice.

How a job runs

  1. 01Survey

    Substrate, service conditions and access, looked at before anything is specified.

  2. 02Specification

    System and material selected, with the standard it will be judged against.

  3. 03Preparation

    Cleaning and surface profile — the step most coating failures trace back to.

  4. 04Application

    Applied by our crews, with the conditions the product needs.

  5. 05Inspection

    Thickness, holiday and adhesion checks, then handover documentation.

Request a quote

Send the asset, the environment and the area and we will come back with a system and a price. Drawings or a scope of work help.

Sends from your own email app to bdm@gipcoating.com. Nothing is stored on this site.

Talk to us first

If the scope is still open, write to us directly and we will answer with the system that fits.

Email
bdm@gipcoating.com
Address
Landstraße 42
60322 Frankfurt am Main
Hessen, Germany
Working
Supply and application worldwide